*FREE SHIPPING*
on all orders over $250

This means you do not pay
any extra fees no matter what.
 No Residential or Liftgate Fees!









 
 
 
     FOLLOW US...
           
 
 
 
 
 
 
 
 
 
 
 
 



You are here:Home > New Metal Forming > Shears
Sort By:
Page of 2
SF-5216E, 52" x 16 Ga. Metal Foot Shear
SF-5216E, 52" x 16 Ga. Metal Foot Shear
Our Price: $2,095.00

When looking for a high quality, economical foot shear for your shop, look no further than the SF-5216E foot shear from Baileigh Industrial.  The SF-5216E foot shear great for those small to medium shops or educational institutions that are on a budget.   But the best thing is that the SF-5216E is still is built to the same standards as all Baileigh Industrial equipment.

The SF-5216E foot shear is able to shear 52” of 16 gauge mild steel.  High chromium blades offer long life and have the ability to be resharpened.  Front supports help the operator with alignment and an integrated back stop allows for repeatability of cut.  A ridged cast frame rounds out the list of impressive features on the SF-5216E.
SF-5216, 52" x 16 Ga. Metal Foot Shear
SF-5216, 52" x 16 Ga. Metal Foot Shear
Our Price: $3,775.00

This heavy duty manual shear is capable of shearing 16 gauge mild steel sheet metal over its entire 52” length.  The SF-5216 is made from solid steel construction for maximum rigidity.  This rigidity helps the shearing process by having less deformation at the start of the cut, which provides a better cut.

The SF-5216 is easy to operate, simply put your material between the blade and the table, and stomp the foot pedal.  There is also a finger guard for safety when shearing.  Other features are a front gauge and back gauge range of 24" for repeatable cuts time and time again.
SH-5216A, 52" x 16 Ga. Pneumatic Metal Shear
SH-5216A, 52" x 16 Ga. Pneumatic Metal Shear
Our Price: $5,770.00

Baileigh Industrial's SH-5216A sheet metal air shear is the perfect for any fabrication or HVAC shop where 16 gauge or lighter material needs to be sheared. The SH-5216A air shear has a capacity of 16 gauge mild steel and will cut up to 52" wide sheet metal. The pneumatic system requires only compressed air between 90 and 115 psi and no electrical power to function. This powerful pneumatic shear can cut at speeds of 20 strokes per minute when high production is required.

Our air shears are built of all steel plate that is fully integrated and welded to last decades. It also uses high chromium carbon blades for long life. These blades have multiple cutting surfaces for extended life between re-sharpening.  Front and back material supports as well as side guides are also included. A manual back gauge that has a hand wheel for quick adjustments is standard, and is perfect for those larger runs where repeatability is required.
SH-5214, 52" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
SH-5214, 52" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
Our Price: $8,710.00

This 52” shear will cut 14 gauge mild steel over its full length and operates on 220 volt single phase power. The SH-5214 comes standard with the adjustable back gauge for precise repeatability. It also comes standard with table guides and front arm extensions.

The SH-5214 is like the other Baileigh Industrial compact hydraulic shears, have the upper carriage is built to minimize any deformation and the upper and lower blades have multiple shearing edges, both extend blade life and save your shop money. The operator console has the controls to jog the upper carriage, produce one cut with one foot pedal push, or remain in an auto mode by holding the foot pedal down. The SH-5214 also has hydraulic hold downs that hold the sheet solidly to the table not allowing the material to lift when being sheared.
SH-6014, 60" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
SH-6014, 60" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
Our Price: $10,390.00

The SH-6014 metal shear uses 60" blades that can cut down to 14 gauge mild steel or 18 gauge stainless steel easily.
This machine is made of fully integrated and welded steel plate allowing enough rigidity to shear at full capacity all day long. Powered by a 3hp 220 volt three phase motor, the industrial hydraulics pull the top blade smoothly through the material being cut increasing blade life.  This metal shears top and bottom shearing blades have multiple cutting edges that extend blade life. The SH-6014 also has a hold down carriage with 9 fingers hold the sheet metal firmly against the in feed table eliminating any lifting of material as it is cut, again this improves blade life.

The SH-6014 hydraulic metal shear has a manual back gauge as well as front support arms to help the operator handle the sheet metal and provide for repeatable shearing. The operator control panel has a switch that allows the fabricator to jog the blade, do one cycle or cut, or go into an automatic mode that is initiated by the foot pedal control.
SH-5210, 52" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
SH-5210, 52" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
Our Price: $13,225.00

This high quality shear has a maximum capacity of 10 gauge mild steel at its full 52” cutting width.  The best part about the SH-5210 is that is operates on 220 volt single phase power, making it perfect for just about any shop.

The SH-5210 hydraulic sheet metal shear has a fully welded rigid frame allowing it to shear metal at full capacity and produces no deflection in the frame or shearing areas, meaning perfect shears every time.  The SH-5210 also comes standard with high carbon chromium blades that can be flipped and resharpened periodically saving the fabricator a lot of money over the life of the machine.

The SH-5210 a simple design that allows for ease of operation, the operator has the controls to jog the upper carriage, produce one cut with one foot pedal push, or remain in an auto mode by holding the foot pedal down. Hold downs clamp the material to the in feed table so the material doesn't lift when being sheared.

An adjustable back gauge, front table gauges and front arm extensions are also standard on the SH-5210.
SH-8014, 80" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
SH-8014, 80" x 14 Ga. Hydraulic Metal Shear ~ 3 HP, 3 Ph
Our Price: $14,380.00

The SH-8014 hydraulic shear from Baileigh industrial is a great shear for those fabrication shops that mainly work with smaller gauge sheet metal.  The SH-8014 metal shear from Baileigh Industrial has an 80" cutting width and can shear up to 14 gauge mild steel. The table of the SH-8014 hydraulic shear is made from ground and polished steel plate allowing enough rigidity to shear at full capacity over and over again. The SH-8014 hydraulic shear can also cut through 18 gauge stainless steel.

Operating on 220 volt three phase power, the industrial grade hydraulics pull the top shearing head with top blade smoothly through the material being cut increasing blade life. The SH-8014 shear has top and bottom blades have multiple cutting edges that extends blade life. The SH-8014 features hydraulic hold downs that hold the sheet metal firmly against the in feed table eliminating any lifting of material as it is cut which improves blade life.
The SH-8014 hydraulic metal shear has a manual back gauge or material stop as well as front support arms to help the operator handle the sheet metal and provide for repeatable shearing. The operator control panel has a switch that allows the fabricator to jog the blade, for accurate blade adjustment, or go into an automatic mode that is initiated by the foot pedal control.
SH-6010, 60" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
SH-6010, 60" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
Our Price: $15,430.00

The SH-6010 hydraulic shear is the perfect machine for any fabrication or sheet metal shop.  It features a 60" wide cutting capacity and is capable of smoothly shearing through 10 gauge mild steel and 13 gauge stainless steel.  These capacities will accommodate most sheet metal applications.

Using powerful industrial grade hydraulics and a fully welded metal plate construction, this machine is built to reduce flex when shearing at full capacity and result in smooth effortless cuts. The smooth movements help extend blade life.  The upper and lower blades have multiple shearing edges, both will help extend blade life and save you money.

The operator has the controls to jog the upper carriage, produce one cut with one foot pedal push, or remain in an auto mode by holding the foot pedal down. Hold downs clamp the material to the in feed table so the material doesn't lift when being sheared.  An adjustable back gauge for repeatability as well as front material supports is also included.
SH-8010, 80" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
SH-8010, 80" x 10 Ga. Hydraulic Metal Shear ~ 5 HP, 3 Ph
Our Price: $18,475.00

Baileigh Industrial’s SH-8010 compact shear has an 80" wide cutting capacity to accommodate most sheet metal applications and is the perfect metal shear for any fabrication shop looking to increase production. Using powerful industrial grade hydraulics controlled by a 220 volt three phase motor, this machine is capable of smoothly shearing through 10 gauge mild steel and 13 gauge stainless steel.

The SH-8010, like the other Baileigh Industrial compact shears, has the upper carriage built to minimize any deformation and the upper and lower blades have multiple shearing edges, both extend blade life. The operator has the controls to jog the upper carriage, produce one cut with one foot pedal push, or remain in an auto mode by holding the foot pedal down. Hydraulic hold downs clamp the sheet solidly to the in feed table so the material doesn't lift when being sheared.  The SH-8010 is built to withstand years of service in just about any environment. The SH-8010 is the perfect hydraulic shear for any fabrication shop.
SH-5210-HD, 52" x 10 Ga. Heavy Duty Hydraulic Metal Shear ~ 7.5 HP, 3 Ph
SH-5210-HD, 52" x 10 Ga. Heavy Duty Hydraulic Metal Shear ~ 7.5 HP, 3 Ph
Our Price: $20,045.00

The SH-5210-HD heavy duty hydraulic shear is a heavy duty machine built for years of production. It will take what you can throw at it and keep coming back for more.  This machine has thick steel plate frame that is fully welded for rigidity.  The shearing carriage rides against hardened carriage ways and uses heavy duty bearings to reduce friction and wear. The industrial grade hydraulics system on the SH-5210-HD is powered by a 7.5 hp 220 volt three phase motor.

The centralized control panel offers the selection of jog, single or continuous cutting modes. There is also a dial for adjusting the rake that eliminates curl and twist in cutting as well as a quick adjustment lever for material thickness.  The upper blade is two sided while the lower blade is four sided. The blades can be resharpened when needed saving money.

This hydraulic sheet metal cutting shear has rigid, heavy duty load table and side gauges.  A light shadow line for shearing position is standard and st the rear of the machine is a manual back gauge for repeatability.
   
 
Metal Forming Catagories
Newsletter

Sign up for our newsletter: